Nokia 6120 unlock problem

[bogdan_meseriasu]

Hy! I have a nokia 6120c and trying to unlock. I have the folowing error:
BB5 Unlock Started...
MCU Version V 03.83
MCU Date 18-06-07
Product RM-243 (Nokia 6120 classic)
Manufacturer (c) Nokia
IMEI 358641016114992
Mastercode 446061042
Simlock Server SIMLOCK SERVER
Simlock Key 2260100007642670
Simlock Profile 8000000000000000
Simlock Key Cnt 0
Simlock FBUS Cnt 0
Simlock [1,1] State: CLOSED Type: MCC-MNC Data: 22601F
Reading Security Block...
Security block OK and saved to "RM-243_358641016114992_25.01.2013_005721.SecurityBloc k.PM"
WARNING: "2260010A178500589A3043EEF312690FF38CF60F.B0001B5B" Not Exists, Will read it...
Reading CYC file from phone...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101021103
CMT_EM_ASIC_ID: 00000295
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 2260010A178500589A3043EEF312690FF38CF60F
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
CMT_BOOT_ROM_CRC: A8C1D671
CMT_SECURE_ROM_CRC: 3E691FF8
CMT Ready!
New_RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.11.16.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC003000000121, Samsung, ONENAND
Requested Algorithm: XSR 1.5 (CMT)
Sending Auxiliary Loader...
Auxiliary Loader Sent!
CBUS Request Error -> CBUS Response wrong header
Failed to Write RAW CMT Data -> Failed to write CMT data data (1)
Failed to Send Custom Code -> Failed to write Stack

I use cyclone box and gpgufc pro 2012.
Please help!

[.::EXTREME::.]

Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again

check its properly connected, if not fix it and try again

[bogdan_meseriasu]

check its properly connected, if not fix it and try again
I use BB5-C conector from GPGUFC PRO. The conection is just fine but still reiving same error. I dont know vhat is wrong. I verified the pinouts from the phone with the pinouts from BB5-C connector. Please help. Any ideea is welcomed. I just have to do this phone so please try and help me. TKX!

[bogdan_meseriasu]

check its properly connected, if not fix it and try again
so? Nobody try to help?
Please. I dont know what to do.
I put new installer 1.22. No can do. Please some suport.