PDA

View Full Version : Successfully repaired VTU00M name 00000000, for GT-i9300



osvah
05-09-2015, 11:45 AM
logs



EasyJtag Suite ver.: 1.5.0.0 / wxWidgets 3.1.0-W-U started.
Operating system ver.: Windows 7 (build 7601, Service Pack 1).
Successefuly connected to box on COM3Box S/N: 1717160DCD0D8A9F, ,FW Ver.: 01.50Box Working Mode: JTAG Box.Box Drivers version: 3.0.0.0, are OK
Z3X Card Serial : AA3B-2511 , ver: 22
Z3X Card Activation [LG] : NOT ACTIVATED , ACTIVATE NOW
Z3X Card Activation [SAMS] : NOT ACTIVATED , ACTIVATE NOW
Z3X Card Activation [JTAG] : ACTIVATED

Z3X EasyJtag Software ver. 1.5.0.0
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 1717160DCD0D8A9F, ,FW Ver.: 01.50
CMD Pullup Level:1825 mV
CMD Active Level:1897 mV
eMMC Device Information
EMMC CID : 1501003030303030305620110726589C
EMMC CSD : 902701320F5903FFF6DBFFEF8A404022
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2005 Rev.0x56
EMMC NAME: 000000 , S/N: 537986854
EMMC ROM1 (Main User Data) Capacity: 16384 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: 000000_ 537986854_20140402_1105.extcsd
Done.
Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...

Z3X EasyJtag Software ver. 1.5.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1825 mV
CMD Active Level:1897 mV
Start EMMC repair:
Entering repair mode 1...
Success
Erasing repair area...
Success
Writing repair area...
Success
Exit repair mode 1...
Success
===================================
Init EMMC...
Can't init EMMC, Reason: CARD Ready Timeout Error
Please, Reconnect EMMC power lines and press 'VTU00M Repair' again
===================================
Successefuly connected to box on COM3Box S/N: 1717160DCD0D8A9F, ,FW Ver.: 01.50Box Working Mode: JTAG Box.Box Drivers version: 3.0.0.0, are OK
Z3X Card Serial : AA3B-2511 , ver: 22
Z3X Card Activation [LG] : NOT ACTIVATED , ACTIVATE NOW
Z3X Card Activation [SAMS] : NOT ACTIVATED , ACTIVATE NOW
Z3X Card Activation [JTAG] : ACTIVATED

Z3X EasyJtag Software ver. 1.5.0.0
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 1717160DCD0D8A9F, ,FW Ver.: 01.50
CMD Pullup Level:1815 mV
CMD Active Level:1887 mV
eMMC Device Information
EMMC CID : 15010056545530304DF17AA34B12AFCA
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 10/2012 Rev.0xf1
EMMC NAME: VTU00M , S/N: 2057521938
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Backup saved: VTU00M_2057521938_20140402_1107.extcsd
Done.

Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...

Z3X EasyJtag Software ver. 1.5.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:2660 mV
CMD Active Level:2722 mV
Start EMMC repair:
Entering repair mode 2...
Success
Erasing repair area...
Success
Writing repair area...
Success
Exit repair mode 2...
Reading S.M.A.R.T
Can't init EMMC, Reason: CMD Timeout Error
===================================
Running:SAMSUNG: Read S.M.A.R.T Report...

Z3X EasyJtag Software ver. 1.5.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:2660 mV
CMD Active Level:2722 mV
Reading S.M.A.R.T
S.M.A.R.T Ver. 0 , Card Error mode : Normal
Super Block size : 0x00800000 (8388608 bytes)
Super Page size : 0x00004000 (16384 bytes)
Optimal Write size : 0x00010000 (65536 bytes)
Read Reclaim count : 0
Optimal TRIM size : 0x00002000 (8192 bytes)
Total Number of banks : 4
Initial bad blocks per bank : 1,1,2,15
Runtime bad blocks per bank : 0,0,0,0
Reserved blocks left per bank : 50,50,49,36
All Erase counts (min,avg,max): 0,0,1
SLC Erase counts (min,avg,max): 0,0,1
MLC Erase counts (min,avg,max): 0,0,0
S.M.A.R.T Report Done !!!

EMMC CID : 15010056545530304DF17AA34B12AFCA
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 10/2012 Rev.0xf1
EMMC NAME: VTU00M , S/N: 537986854
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Backup saved: VTU00M_2057521938_20140402_1138.extcsd
Done.
Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...

Z3X EasyJtag Software ver. 1.5.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:2660 mV
CMD Active Level:2722 mV
Start EMMC repair:
Entering repair mode 2...
Success
Erasing repair area...
Success
Writing repair area...
Success
Exit repair mode 2...
Reading S.M.A.R.T
Can't init EMMC, Reason: CMD Timeout Error
===================================
Running:SAMSUNG: Read S.M.A.R.T Report...

Z3X EasyJtag Software ver. 1.5.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:2660 mV
CMD Active Level:2722 mV
Reading S.M.A.R.T
S.M.A.R.T Ver. 0 , Card Error mode : Normal
Super Block size : 0x00800000 (8388608 bytes)
Super Page size : 0x00004000 (16384 bytes)
Optimal Write size : 0x00010000 (65536 bytes)
Read Reclaim count : 0
Optimal TRIM size : 0x00002000 (8192 bytes)
Total Number of banks : 4
Initial bad blocks per bank : 1,1,2,15
Runtime bad blocks per bank : 0,0,0,0
Reserved blocks left per bank : 50,50,49,36
All Erase counts (min,avg,max): 0,0,1
SLC Erase counts (min,avg,max): 0,0,1
MLC Erase counts (min,avg,max): 0,0,0
S.M.A.R.T Report Done !!!

Z3X EasyJtag Software ver. 1.5.0.0
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 1717160DCD0D8A9F, ,FW Ver.: 01.50
CMD Pullup Level:1804 mV
CMD Active Level:1887 mV
eMMC Device Information
EMMC CID : 15010056545530304DF17AA34B12AFCA
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 10/2012 Rev.0xf1
EMMC NAME: VTU00M , S/N: 537986854
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: VTU00M_2057521938_20140402_1139.extcsd
Done.
Writing file...E:\ALL DEVISES\z3x\9. Easy Jtag files\Samsung\GT-I9300\Dump\EMMC_ROM2_00000000_00200000.bin

Z3X EasyJtag Software ver. 1.5.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1804 mV
CMD Active Level:1887 mV
Writing 000000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Write Speed: 819 kB/s
Done !!!
Writing file...E:\ALL DEVISES\z3x\9. Easy Jtag files\Samsung\GT-I9300\Dump\EMMC_ROM1_00000000_20000000.bin

Z3X EasyJtag Software ver. 1.5.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1804 mV
CMD Active Level:1887 mV
Writing 000020000000 bytes to 00000000 ...ROM1 (USER ROM)
Write Speed: 836 kB/s
Done !!!

thanks z3x team.best in the world