Page 1 of 2 12 LastLast
Results 1 to 10 of 20
  1. #1
    Junior Member
    Join Date
    Dec 2011
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts

    spd 6530 chips problem pls help

    this phone model was itel it6100 label at the back, it was security code, try with gpg 3.17b, when not unlock, i format then u disk error, when i now format with valcano cant power anymore only flashlight on. try to file readed from u disk error but cant flash
    Attached Images Attached Images

  2. #2
    Senior Member
    Join Date
    Oct 2011
    Location
    Kick Mode Activated!!! Be Care.
    Posts
    770
    Thanks
    64
    Thanked 687 Times in 179 Posts
    try with low baudrate to write this file....

    is that original backup?

    ifso try to read code from flashfile

  3. #3
    Junior Member
    Join Date
    Dec 2011
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    already try that still not work,it seem it a bug on software pls volcano team fix this asap thanks

  4. #4
    Junior Member
    Join Date
    Nov 2011
    Posts
    1
    Thanks
    0
    Thanked 0 Times in 0 Posts
    try to use low baudrate to 115200...then writing flash file ok...

  5. #5
    Junior Member
    Join Date
    Dec 2011
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    still not working, 115200 baurate will show this log Port:COM13
    After format or Flash you have to press & hold power button for at least 1.30 mins.
    SPD U Disk Error Flash files password is = VolcanoAheadOfAllEVER
    Available Ports:COM13 COM90 COM91
    Detection initiated...
    Failed to connect, please try again.
    Pinouts are not fonud!
    Detection initiated...
    Vcc: null
    Gnd: 5
    Analyzing D+ and D-...
    D+ = 3, D- = 2
    Detection D+/D- with 1.56 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    BOOT(Pull Down) = 4
    Setting...
    Find USB device:SCI USB2Serial (COM45), (VID_1782&PID_4D00)
    Pinouts setting complete!


    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Please put the baud set 115200, try again.
    >>Ready to read/write again, please remove the power supply clip or battery and then re-loaded it.

    while other baud rate will show this

    Detection initiated...
    Vcc: null
    Gnd: 5
    Analyzing D+ and D-...
    D+ = 3, D- = 2
    Detection D+/D- with 1.73 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    BOOT(Pull Down) = 4
    Setting...
    Find USB device:SCI USB2Serial (COM45), (VID_1782&PID_4D00)
    Pinouts setting complete!


    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6530 [65300000]
    FLASH ID: 00C8006000170000
    Flash Type:[GD] 25LG64bWL
    Size:0x800000(8MB)
    >>Writing...(0)



    im very sure its a bug, pls volcano team fix this asap

  6. #6
    Junior Member
    Join Date
    Nov 2011
    Posts
    7
    Thanks
    7
    Thanked 5 Times in 3 Posts
    [QUOTE=segnattech;31558]still not working, 115200 baurate will show this log Port:COM13
    After format or Flash you have to press & hold power button for at least 1.30 mins.
    SPD U Disk Error Flash files password is = VolcanoAheadOfAllEVER
    Available Ports:COM13 COM90 COM91
    Detection initiated...
    Failed to connect, please try again.

    TRY BAUDRATE 460800

  7. #7
    Junior Member
    Join Date
    Jan 2012
    Posts
    1
    Thanks
    0
    Thanked 0 Times in 0 Posts
    pls anybody with itel it6100 flash to post it pls urgently needed

  8. #8
    Junior Member
    Join Date
    May 2012
    Posts
    10
    Thanks
    0
    Thanked 1 Time in 1 Post
    agtel ice dead after flash in volcano box pleas......... give solution for problem

  9. #9
    Junior Member
    Join Date
    Nov 2011
    Location
    pune
    Posts
    20
    Thanks
    0
    Thanked 2 Times in 2 Posts
    Analyzing D+ and D-...
    D+ = 9, D- = 8
    Analyzing USB device, please wait...
    Find USB device:SPRD U2S Diag (COM8), (VID_1782&PID_4D00)


    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6530 [65300000]
    FLASH ID: 00C8006000170000
    Flash Type:[GD] 25LG64bWL
    >>Size:0x800000(8MB)
    aftar formet dade phone

  10. #10
    Junior Member
    Join Date
    Nov 2011
    Posts
    24
    Thanks
    0
    Thanked 1 Time in 1 Post
    hehehe sorry sorry i have already dead 2 handset....after format in dragon handset dead. when i try to flash with backup file..

    showing error Error CODE:FF--> CMD_EERPR --> UNKNOWN


    its party time.......gpg dragon giving mind blowing update for dragon user........

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •