Results 1 to 4 of 4
  1. #1
    Junior Member
    Join Date
    Oct 2012
    Posts
    5
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Nokia 6120 unlock problem

    Hy! I have a nokia 6120c and trying to unlock. I have the folowing error:
    BB5 Unlock Started...
    MCU Version V 03.83
    MCU Date 18-06-07
    Product RM-243 (Nokia 6120 classic)
    Manufacturer (c) Nokia
    IMEI 358641016114992
    Mastercode 446061042
    Simlock Server SIMLOCK SERVER
    Simlock Key 2260100007642670
    Simlock Profile 8000000000000000
    Simlock Key Cnt 0
    Simlock FBUS Cnt 0
    Simlock [1,1] State: CLOSED Type: MCC-MNC Data: 22601F
    Reading Security Block...
    Security block OK and saved to "RM-243_358641016114992_25.01.2013_005721.SecurityBloc k.PM"
    WARNING: "2260010A178500589A3043EEF312690FF38CF60F.B0001B5B " Not Exists, Will read it...
    Reading CYC file from phone...
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101021103
    CMT_EM_ASIC_ID: 00000295
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 2260010A178500589A3043EEF312690FF38CF60F
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
    CMT_BOOT_ROM_CRC: A8C1D671
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    New_RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.11.16.0, Algo: BB5
    Flashbus Write baud set to 1.0Mbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    If software STUCK HERE with box TX LED lit, that means:
    1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
    2. Your cable is not TX2 Enabled!
    3. Transmission error occured, try again
    In either cases, you need to reconnect your box from USB.
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC003000000121, Samsung, ONENAND
    Requested Algorithm: XSR 1.5 (CMT)
    Sending Auxiliary Loader...
    Auxiliary Loader Sent!
    CBUS Request Error -> CBUS Response wrong header
    Failed to Write RAW CMT Data -> Failed to write CMT data data (1)
    Failed to Send Custom Code -> Failed to write Stack

    I use cyclone box and gpgufc pro 2012.
    Please help!

  2. #2
    Senior Member
    Join Date
    Oct 2011
    Location
    Kick Mode Activated!!! Be Care.
    Posts
    770
    Thanks
    64
    Thanked 687 Times in 179 Posts
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    If software STUCK HERE with box TX LED lit, that means:
    1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
    2. Your cable is not TX2 Enabled!
    3. Transmission error occured, try again
    check its properly connected, if not fix it and try again

  3. #3
    Junior Member
    Join Date
    Oct 2012
    Posts
    5
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Quote Originally Posted by .::EXTREME::. View Post
    check its properly connected, if not fix it and try again
    I use BB5-C conector from GPGUFC PRO. The conection is just fine but still reiving same error. I dont know vhat is wrong. I verified the pinouts from the phone with the pinouts from BB5-C connector. Please help. Any ideea is welcomed. I just have to do this phone so please try and help me. TKX!

  4. #4
    Junior Member
    Join Date
    Oct 2012
    Posts
    5
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Quote Originally Posted by .::EXTREME::. View Post
    check its properly connected, if not fix it and try again
    so? Nobody try to help?
    Please. I dont know what to do.
    I put new installer 1.22. No can do. Please some suport.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •