Page 1 of 2 12 LastLast
Results 1 to 10 of 14
  1. #1
    Board of Directors
    Join Date
    Apr 2015
    Posts
    5,560
    Thanks
    2
    Thanked 52 Times in 41 Posts

    Repairing SC6531 With Volcano is So Easy That I Wish All Faulty Mobiles have This CPU

    Repairing SC6531/SC6531D/SC6531DA With Volcano is So Easy That I Wish All Incoming Faulty Mobiles Were SC6531

    Till Date I have Repaired More Than 5000 SC6531 Handsets, Only 2-3 of them I had returned to Customer Just Because Of Bad Flash Files, Otherwise All Handsets were revived Successfully.

    Only Following Below Given Universal Method (Most Of You Know This Very Well) :

    * READ FLASH FILE
    * LOAD/SELECT YOUR READED FLASH FILE
    * DO FORMAT
    (Check Now if phone got ok)

    If Not Got Ok, then
    * WRITE FLASH FILE
    * AGAIN DO FORMAT
    (Check Now phone got ok)

    NOTE : Best Way to check Phone is On Volcano Eagle Eye.

    OR Insert Full Charged Battery & Press Power Button for atleast 1minute

    I'll Post Many Logs Here To Show You All People That Volcano is Not A Useless Device As Many Of You People Always Blame. Please Check & Observe All Logs Carefully.

    If You Want Flash Files, You can Find It in Volcano Flash Files Section Or On My Support.

  2. #2
    Board of Directors
    Join Date
    Apr 2015
    Posts
    5,560
    Thanks
    2
    Thanked 52 Times in 41 Posts
    ZEN X13 Blinking Repair Done
    Code:
    Detection initiated...
    Vcc: null
    Gnd: 5
    Analyzing D+ and D-...
    D+ = 3, D- = 2
    Detection D+/D- with 1.34 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
    Setting...
    Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
    Pinouts setting complete!


    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6531 [65310000]
    FLASH ID: 00C8006000160000
    Flash Type:[GD] 25LG32bWL
    Size:0x400000(4MB)
    Reading completed.
    The data has been saved in D:\FLASH FILES\SC6531\ZEN X13 {SC6531 [GD] 25LG32bWL} Cable - 05b.bin, size: 4 M.
    Detection initiated...
    Vcc: null
    Gnd: 5
    Analyzing D+ and D-...
    D+ = 3, D- = 2
    Detection D+/D- with 1.31 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
    Setting...
    Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
    Pinouts setting complete!

    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6531 [65310000]
    FLASH ID: 00C8006000160000
    Flash Type:[GD] 25LG32bWL
    Size:0x400000(4MB)
    >>Set to Factory successfully.

  3. #3
    Board of Directors
    Join Date
    Apr 2015
    Posts
    5,560
    Thanks
    2
    Thanked 52 Times in 41 Posts
    ZEN X13 (V1) Blinking Repair Done
    Code:
    Detection initiated...
    Vcc: null
    Gnd: 5
    Analyzing D+ and D-...
    D+ = 3, D- = 2
    Detection D+/D- with 1.30 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
    Setting...
    Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
    Pinouts setting complete!


    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6531 [65310001]
    FLASH ID: 00C8006000160000
    Flash Type: SF_GD25LQ32
    Size:0x400000(4MB)
    Reading completed.
    The data has been saved in D:\FLASH FILES\SC6531\ZEN X13 (V1) {SC6531 [SF_GD25LQ32]} Cable - 05b Press LSK.bin, size: 4 M.
    Detection initiated...
    Vcc: null
    Gnd: 5
    Analyzing D+ and D-...
    D+ = 3, D- = 2
    Detection D+/D- with 1.33 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
    Setting...
    Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
    Pinouts setting complete!

    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6531 [65310001]
    FLASH ID: 00C8006000160000
    Flash Type: SF_GD25LQ32
    Size:0x400000(4MB)
    >>Set to Factory successfully.

  4. #4
    Board of Directors
    Join Date
    Apr 2015
    Posts
    5,560
    Thanks
    2
    Thanked 52 Times in 41 Posts
    ZEN X12 Dead Repair Done
    Code:
    Detection initiated...
    Vcc: null
    Gnd: 5
    Analyzing D+ and D-...
    D+ = 3, D- = 2
    Detection D+/D- with 1.28 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
    Setting...
    Find USB device:SCI USB2Serial (COM165), (VID_1782&PID_4D00)
    Pinouts setting complete!


    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6531 [65310000]
    FLASH ID: 00EF004000160000
    Flash Type:[WinBond] W25Q32BV
    Size:0x400000(4MB)
    Reading completed.
    The data has been saved in C:\Documents and Settings\Shanu\Desktop\_20141128_143541_FullFlash zen x12.bin, size: 4 M.
    Detection initiated...
    Vcc: null
    Gnd: 5
    Analyzing D+ and D-...
    D+ = 3, D- = 2
    Detection D+/D- with 1.20 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
    Setting...
    Find USB device:SCI USB2Serial (COM165), (VID_1782&PID_4D00)
    Pinouts setting complete!

    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6531 [65310000]
    FLASH ID: 00EF004000160000
    Flash Type:[WinBond] W25Q32BV
    Size:0x400000(4MB)

  5. #5
    Board of Directors
    Join Date
    Apr 2015
    Posts
    5,560
    Thanks
    2
    Thanked 52 Times in 41 Posts
    ZEN X9i Dead Repair Done
    Code:
    For many phones, charge pins need to be set in order to identify USB devices.
    Detecting D+ and D-...
    Vcc: null
    Gnd: 5
    Detection initiated...
    D+ = 3, D- = 2
    Detection D+/D- with 1.73 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
    Detection completed.
    Available Ports:COM1 COM3 COM4
    Detection initiated...
    Vcc: null
    Gnd: 5
    Analyzing D+ and D-...
    D+ = 3, D- = 2
    Detection D+/D- with 1.31 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
    Setting...
    Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
    Pinouts setting complete!


    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6531 [65310001]
    FLASH ID: 00C8006000160000
    Flash Type: SF_GD25LQ32
    Size:0x400000(4MB)
    Reading completed.
    The data has been saved in D:\FLASH FILES\SC6531\ZEN X9i {SC6531 [SF_GD25LQ32]} Cable - 05b.bin, size: 4 M.
    Detection initiated...
    Vcc: null
    Gnd: 5
    Analyzing D+ and D-...
    D+ = 3, D- = 2
    Detection D+/D- with 1.31 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
    Setting...
    Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
    Pinouts setting complete!

    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6531 [65310001]
    FLASH ID: 00C8006000160000
    Flash Type: SF_GD25LQ32
    Size:0x400000(4MB)
    >>Set to Factory successfully.

  6. #6
    Board of Directors
    Join Date
    Apr 2015
    Posts
    5,560
    Thanks
    2
    Thanked 52 Times in 41 Posts
    ZEN X4i Dead Repair Done
    Code:
    For many phones, charge pins need to be set in order to identify USB devices.
    Detecting D+ and D-...
    Vcc: null
    Gnd: 5
    Detection initiated...
    D+ = 3, D- = 2
    Detection D+/D- with 1.50 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
    Detection completed.
    Available Ports:COM1 COM3 COM4
    Detection initiated...
    Vcc: null
    Gnd: 5
    Analyzing D+ and D-...
    D+ = 3, D- = 2
    Detection D+/D- with 1.28 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
    Setting...
    Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
    Pinouts setting complete!


    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6531 [65310001]
    FLASH ID: 00C8006000160000
    Flash Type: SF_GD25LQ32
    Size:0x400000(4MB)
    Reading completed.
    The data has been saved in D:\FLASH FILES\SC6531\ZEN X4i {SC6531 [SF_GD25LQ32]} Cable -

  7. #7
    Board of Directors
    Join Date
    Apr 2015
    Posts
    5,560
    Thanks
    2
    Thanked 52 Times in 41 Posts
    ZEN X4 Dead Repair Done
    Code:
    Detection initiated...
    Vcc: 10
    Gnd: 1 4
    Analyzing D+ and D-...
    D+ = 9, D- = 8
    Detection D+/D- with 1.74 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    BOOT(Pull Down) = 6
    Setting...
    Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
    Pinouts setting complete!


    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6531 [65310000]
    FLASH ID: 00EF004000160000
    Flash Type:[WinBond] W25Q32BV
    Size:0x400000(4MB)
    Reading completed.
    The data has been saved in D:\FLASH FILES\SC6531\ZEN X4 {SC6531 [WinBond] W25Q32BV} Cable - 12c by Moiz Khan.bin, size: 4 M.
    Detection initiated...
    Vcc: 10
    Gnd: 1 4
    Analyzing D+ and D-...
    D+ = 9, D- = 8
    Detection D+/D- with 1.30 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    BOOT(Pull Down) = 6
    Setting...
    Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
    Pinouts setting complete!

    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6531 [65310000]
    FLASH ID: 00EF004000160000
    Flash Type:[WinBond] W25Q32BV
    Size:0x400000(4MB)
    >>Set to Factory successfully.

  8. #8
    Board of Directors
    Join Date
    Apr 2015
    Posts
    5,560
    Thanks
    2
    Thanked 52 Times in 41 Posts
    ZEN P37 (16MB) Dead Repair Done
    Code:
    Available Ports:COM1 COM4 COM112
    Detection initiated...
    Vcc: null
    Gnd: 5
    Analyzing D+ and D-...
    D+ = 3, D- = 2
    Detection D+/D- with 1.38 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
    Setting...
    Find USB device:SCI USB2Serial (COM113), (VID_1782&PID_4D00)
    Pinouts setting complete!


    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6531 [65310000]
    FLASH ID: 00C8006000180000
    Flash Type:[GD] 25LQ128YIG
    Size:0x1000000(16MB)
    Reading completed.
    The data has been saved in C:\Documents and Settings\Shanu\Desktop\_20141115_190307_FullFlash Zen P37.bin, size: 16 M.
    Detection initiated...
    Vcc: null
    Gnd: 5
    Analyzing D+ and D-...
    D+ = 3, D- = 2
    Detection D+/D- with 1.20 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
    Setting...
    Find USB device:SCI USB2Serial (COM113), (VID_1782&PID_4D00)
    Pinouts setting complete!

    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6531 [65310000]
    FLASH ID: 00C8006000180000
    Flash Type:[GD] 25LQ128YIG
    Size:0x1000000(16MB)
    >>Set to Factory successfully.

  9. #9
    Board of Directors
    Join Date
    Apr 2015
    Posts
    5,560
    Thanks
    2
    Thanked 52 Times in 41 Posts
    ZEN M14 Blinking Repair Done

    Code:
    Detection initiated...
    Vcc: null
    Gnd: 5
    Analyzing D+ and D-...
    D+ = 3, D- = 2
    Detection D+/D- with 1.08 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
    Setting...
    Find USB device:SCI USB2Serial (COM165), (VID_1782&PID_4D00)
    Pinouts setting complete!


    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6531 [65310001]
    FLASH ID: 00C8006000160000
    Flash Type: SF_GD25LQ32
    Size:0x400000(4MB)
    Reading completed.
    The data has been saved in C:\Documents and Settings\Shanu\Desktop\_20141122_142201_FullFlash ZEN M14.bin, size: 4 M.
    Detection initiated...
    Vcc: null
    Gnd: 5
    Analyzing D+ and D-...
    D+ = 3, D- = 2
    Detection D+/D- with 1.09 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
    Setting...
    Find USB device:SCI USB2Serial (COM165), (VID_1782&PID_4D00)
    Pinouts setting complete!

    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6531 [65310001]
    FLASH ID: 00C8006000160000
    Flash Type: SF_GD25LQ32
    Size:0x400000(4MB)
    >>Set to Factory successfully.

  10. #10
    Board of Directors
    Join Date
    Apr 2015
    Posts
    5,560
    Thanks
    2
    Thanked 52 Times in 41 Posts
    ZEN M7 Dead Repair Done
    Code:
    Detection initiated...
    Vcc: null
    Gnd: 5
    Analyzing D+ and D-...
    D+ = 3, D- = 2
    Detection D+/D- with 1.31 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
    Setting...
    Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
    Pinouts setting complete!


    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6531 [65310000]
    FLASH ID: 00C8006000160000
    Flash Type:[GD] 25LG32bWL
    Size:0x400000(4MB)
    Reading completed.
    The data has been saved in D:\FLASH FILES\SC6531\ZEN M7 {SC6531 [GD] 25LG32bWL} Cable - 05b press star button.bin, size: 4 M.
    Detection initiated...
    Vcc: null
    Gnd: 5
    Analyzing D+ and D-...
    D+ = 3, D- = 2
    Detection D+/D- with 1.67 seconds.
    Continue to detect BOOT pin...
    Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
    UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
    Setting...
    Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
    Pinouts setting complete!

    Internal version: SPRD3
    Boot downloaded.
    Start boot please wait a moment....
    Spreadtrum Boot Block version 1.2
    CPU TYPE:SC6531 [65310000]
    FLASH ID: 00C8006000160000
    Flash Type:[GD] 25LG32bWL
    Size:0x400000(4MB)
    >>Set to Factory successfully.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •