Page 9 of 9 FirstFirst ... 789
Results 81 to 87 of 87
  1. #81
    Board of Directors
    Join Date
    Apr 2015
    Posts
    5,610
    Thanks
    2
    Thanked 54 Times in 42 Posts
    V1.8.3 - boot repair via USB for LG D851, D620/K/R and more!
    Octoplus JTAG Software v.1.8.3 is out!

    We have added boot repair via USB and small TP for LG G3 D851, G2 Mini LTE-A D620, LG D620K, LG D620R
    and via JTAG for ViewSonic ViewPad 7 (VS13761).


    Octoplus Box JTAG Software v.1.8.3 Release Notes

    • Added support for the following models:


    - LG D851 - added Dead Boot / Device Repair via USB
    - LG D620 - added Dead Boot Repair via USB
    - LG D620K - added Dead Boot Repair via USB
    - LG D620R - added Dead Boot Repair via USB
    - ViewSonic ViewPad 7 (VS13761) - added Dead Boot / Device Repair via JTAG (thanks to Mr. Dr_Wolodya)
    • Uploaded new Full Flash and Repair files for ZTE MF100 (128MB) (thanks to Mr. Dr_Wolodya)
    • All pinouts and Repair procedures are described in the manual ("Help" button in Software)


    To repair mentioned above devices via USB, please follow the next three steps:
    1. Attach testpoint as shown on Figure 1 in the Software manual and connect your phone using Micro USB cable directly into the mainboard’s USB port
      (do NOT use any USB hubs!)
    2. Check PC Device Manager, a new device should appear "Qualcomm HS-USB QDLoader 9008" or "Unknown Device" if you hadn’t installed the driver yet.
      Drivers are in {Installation_Folder}\Driver\QHSUSB
    3. Release testpoint and press “EasyRepair” button in the software (or “Connect” button, when in Advanced Mode)




    http://www.youtube.com/watch?v=YL9sPeXoGWU


    Find out more at: www.octoplusbox.com

  2. #82
    Board of Directors
    Join Date
    Apr 2015
    Posts
    5,610
    Thanks
    2
    Thanked 54 Times in 42 Posts
    V1.8.4 - added boot repair (all in Test Mode) via USB for LG G3 D852, D855 and more.
    Octoplus JTAG Software v.1.8.4 is out!

    We have added boot repair (all in Test Mode) via USB and small TP for LG G3 D852, D852G, D855, D855K and D855P.

    Octoplus Box JTAG Software v.1.8.4 Release Notes

    • Added support for the following models:

    - LG D852 - added Dead Boot Repair via USB (Beta)
    - LG D852G - added Dead Boot Repair via USB (Beta)
    - LG D855 - added Dead Boot Repair via USB (Beta)
    - LG D855K - added Dead Boot Repair via USB (Beta)
    - LG D855P - added Dead Boot Repair via USB (Beta)
    • All pinouts and Repair procedures are described in the manual ("Help" button in Software)


    To repair mentioned above devices via USB, please follow the next three steps:
    1. Attach testpoint as shown on Figure 1 in the Software manual and connect your phone using Micro USB cable directly into the mainboard’s USB port
      (do NOT use any USB hubs!)
    2. Check PC Device Manager, a new device should appear "Qualcomm HS-USB QDLoader 9008" or "Unknown Device" if you hadn’t installed the driver yet.
      Drivers are in {Installation_Folder}\Driver\QHSUSB
    3. Release testpoint and press “EasyRepair” button in the software (or “Connect” button, when in Advanced Mode)




    Find out more at: www.octoplusbox.com

  3. #83
    Board of Directors
    Join Date
    Apr 2015
    Posts
    5,610
    Thanks
    2
    Thanked 54 Times in 42 Posts
    V1.8.5 - added boot repair for LG F160LV/K/S, ZTE P752D, Huawei E171.
    Octoplus JTAG Software v.1.8.5 is out!

    We have added Boot Repair via USB and small TP for LG Optimus LTE II F160LV, LG F160K, LG F160S
    and via JTAG for ZTE P752D (Vodafone Smart Chat V865) and Huawei E171 (CPU: HiSilicon HI6731)!


    Octoplus Box JTAG Software v.1.8.5 Release Notes

    • Added support for the following models:

    - LG F160LV - added Dead Boot / Device Repair via USB
    - LG F160K - added Dead Boot Repair via USB
    - LG F160S - added Dead Boot Repair via USB
    - Huawei E171 (CPU: HiSilicon HI6731) - added Dead Boot / Device Repair via JTAG
    - ZTE P752D - added Dead Boot / Device Repair via JTAG (thanks to Mr. Dr_Wolodya)
    • All pinouts and Repair procedures are described in the manual ("Help" button in Software)


    To repair mentioned above devices via USB, please follow the next three steps:
    1. Attach testpoint as shown on Figure 1 in the Software manual and connect your phone using Micro USB cable directly into the mainboard’s USB port
      (do NOT use any USB hubs!)
    2. Check PC Device Manager, a new device should appear "Qualcomm HS-USB QDLoader 9008" or "Unknown Device" if you hadn’t installed the driver yet.
      Drivers are in {Installation_Folder}\Driver\QHSUSB
    3. Release testpoint and press “EasyRepair” button in the software (or “Connect” button, when in Advanced Mode)





    http://www.youtube.com/watch?v=glWbm1bvrCw




  4. #84
    Board of Directors
    Join Date
    Apr 2015
    Posts
    5,610
    Thanks
    2
    Thanked 54 Times in 42 Posts
    V1.8.6 - added Boot Repair for LG F70 F370K/L/S and LG Optimus LTE II F160LV/K/S.
    Octoplus JTAG Software v.1.8.6 is out!

    We have added Boot Repair via JTAG for LG Optimus LTE II F160LV, LG F160K, LG F160S
    and via USB and small TP for LG F70 F370K, LG F370L, F370S.


    Octoplus Box JTAG Software v.1.8.6 Release Notes

    • Added support for the following models:

    - LG F160LV - added Dead Boot/Device Repair via JTAG
    - LG F160K - added Dead Boot Repair via JTAG
    - LG F160S - added Dead Boot Repair via JTAG
    - LG F370K - added Dead Boot Repair via USB
    - LG F370L - added Dead Boot Repair via USB
    - LG F370S - added Dead Boot Repair via USB
    • All pinouts and Repair procedures are described in the manual ("Help" button in Software)


    To repair mentioned above devices via USB, please follow the next three steps:
    1. Attach testpoint as shown on Figure 1 in the Software manual and connect your phone using Micro USB cable directly into the mainboard’s USB port
      (do NOT use any USB hubs!)
    2. Check PC Device Manager, a new device should appear "Qualcomm HS-USB QDLoader 9008" or "Unknown Device" if you hadn’t installed the driver yet.
      Drivers are in {Installation_Folder}\Driver\QHSUSB
    3. Release testpoint and press “EasyRepair” button in the software (or “Connect” button, when in Advanced Mode)





    http://www.youtube.com/watch?v=SA_zGLxmtHU




  5. #85
    Board of Directors
    Join Date
    Apr 2015
    Posts
    5,610
    Thanks
    2
    Thanked 54 Times in 42 Posts
    V1.8.7 - added Boot Repair for LG VS930, TeXet TM-3200R, Crius Q7A, Huawei G520-0000!
    Octoplus JTAG Software v.1.8.7 is out!

    We have added Boot Repair via USB and small TP for LG VS930 and LG F160L
    and via JTAG for TeXet TM-3200R, Crius Q7A and Huawei G520-0000!


    Octoplus Box JTAG Software v.1.8.7 Release Notes

    • Added support for the following models:

    - LG VS930 - added Dead Boot Repair via USB
    - LG F160L - added Dead Boot Repair via USB
    - TeXet TM-3200R - Dead Boot/Device Repair via JTAG (thanks to mr. Drunya_L)
    - Crius Q7A - Dead Boot / Device Repair via JTAG (thanks to mr. DZ_Developer)
    - Huawei G520-0000 - added Dead Boot Repair via JTAG (thanks to mr. Dr_Wolodya)
    • All pinouts and Repair procedures are described in the manual ("Help" button in Software)


    To repair LG VS930 and LG F160L via USB, please follow the next three steps:
    1. Attach testpoint as shown on Figure 1 in the Software manual and connect your phone using Micro USB cable directly into the mainboard’s USB port
      (do NOT use any USB hubs!)
    2. Check PC Device Manager, a new device should appear "Qualcomm HS-USB QDLoader 9008" or "Unknown Device" if you hadn’t installed the driver yet.
      Drivers are in {Installation_Folder}\Driver\QHSUSB
    3. Release testpoint and press “EasyRepair” button in the software (or “Connect” button, when in Advanced Mode)








  6. #86
    Board of Directors
    Join Date
    Apr 2015
    Posts
    5,610
    Thanks
    2
    Thanked 54 Times in 42 Posts
    V1.8.8 - added Boot Repair via USB and small TP for LG D165G, D415RD, VS870 and more!
    Octoplus JTAG Software v.1.8.8 is out!

    We have added Boot Repair via USB and small TP for LG D165G, LG D415RD, LG VS870
    and via JTAG for HTC HD7 (PD29100) and Huawei E586!


    Octoplus Box JTAG Software v.1.8.8 Release Notes

    • Added support for the following models:


    - LG D165G - added Dead Boot Repair via USB
    - LG D415RD - added Dead Boot Repair via USB
    - LG VS870 - added Dead Boot / Device Repair via USB
    - HTC HD7 (PD29100) - added Dead Boot Repair, Repair IMEI, Repair CID, Read Codes via JTAG (thanks to mr. Chromgsmunlock)
    - Huawei E586 - added Dead Boot Repair via JTAG (thanks to mr. Dr_Wolodya)
    • All pinouts and Repair procedures are described in the manual ("Help" button in Software)


    To repair LG D165G, LG D415RD and LG VS870 via USB, please follow the next three steps:
    1. Attach testpoint as shown on Figure 1 in the Software manual and connect your phone using Micro USB cable directly into the mainboard’s USB port
      (do NOT use any USB hubs!)
    2. Check PC Device Manager, a new device should appear "Qualcomm HS-USB QDLoader 9008" or "Unknown Device" if you hadn’t installed the driver yet.
      Drivers are in {Installation_Folder}\Driver\QHSUSB
    3. Release testpoint and press “EasyRepair” button in the software (or “Connect” button, when in Advanced Mode)




    http://www.youtube.com/watch?v=oev1jcxD1TU



  7. #87
    Board of Directors
    Join Date
    Apr 2015
    Posts
    5,610
    Thanks
    2
    Thanked 54 Times in 42 Posts
    V1.8.9 - added Boot Repair via USB and small TP for LG P930, LU6200 and more!
    Octoplus JTAG Software v.1.8.9 is out!

    We have added Boot Repair via USB and small TP for LG P930, LG LU6200
    and via JTAG for HTC One M7 (PN0720000) and Huawei Y300-0000!


    Octoplus Box JTAG Software v.1.8.9 Release Notes

    • Added support for the following models:

    - LG P930 - added Dead Boot Repair via USB
    - LG LU6200 - added Dead Boot Repair via USB
    - HTC One M7 (PN0720000) - added Dead Boot Repair, Repair IMEI, Repair CID via JTAG
    - Huawei Y300-0000 - added Dead Boot Repair via JTAG (thanks to Mr. Dr_Wolodya)
    • All pinouts and Repair procedures are described in the manual ("Help" button in Software)


    To repair LG P930 and LG LU6200 via USB, please follow the next three steps:
    1. Attach testpoint as shown on Figure 1 in the Software manual and connect your phone using Micro USB cable directly into the mainboard’s USB port
      (do NOT use any USB hubs!)
    2. Check PC Device Manager, a new device should appear "Qualcomm HS-USB QDLoader 9008" or "Unknown Device" if you hadn’t installed the driver yet.
      Drivers are in {Installation_Folder}\Driver\QHSUSB
    3. Release testpoint and press “EasyRepair” button in the software (or “Connect” button, when in Advanced Mode)




    http://www.youtube.com/watch?v=cv258XftyEg



    http://www.youtube.com/watch?v=_pXFuuoOXBk




Page 9 of 9 FirstFirst ... 789

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •